DSG SWAP ELECTRONICS
DSG Controller
Bring the gearbox, ECU and vehicle signals together.
A dedicated interface for DSG conversions, with separate DSG and vehicle CAN connections, paddle inputs, vehicle outputs and configurable signal integration.
Requires a compatible VAG ECU with CAN bus. This is not a standalone DSG controller.
For custom DSG swap projects. Check the gearbox, ECU and required functions for your installation before ordering.
DSG Controller and wiring loom
⇄ Two CAN connections
↕ Digital & LIN paddles
◉ VSS & vehicle outputs
⌁ Wireless updates
WHAT IT DOES
Connect your DSG conversion to the rest of the car
A DSG swap brings together a transmission, an ECU and vehicle electronics that may come from different platforms. Their signals need to work together for the conversion to function as intended.
The DSG Controller provides a dedicated CAN connection for the DSG and another for the car or ECU, alongside conventional inputs and outputs. It combines signal conversion with the connections needed for paddles, brake signals, the speedometer, reverse lights and starter enable.
The DSG Controller is not a standalone transmission controller. It requires a compatible VAG ECU with CAN bus, and the original DSG transmission control unit remains part of the installation.
Car / ECU
Vehicle CAN · CAN1
⇄
DSG Controller
Signal conversion + configurable I/O
⇄
DSG gearbox
DSG CAN · CAN0
↓
VSS speed signal
Reverse lights
Starter-enable relay
Functional overview. Use the wiring schematic for installation.
Black and grey connectors keep the controller wiring grouped.
VEHICLE OUTPUTS
Keep the everyday vehicle functions working
The controller brings DSG status back to the conventional electrical connections used in older vehicles.
✓ Reverse lights: a dedicated 12 V reverse-light output.
✓ Starter enable: a 12 V output for a relay, enabled with the selector in P or N.
✓ VSS speedometer: a speed signal for compatible instrument clusters without CAN.
✓ Torque reduction: a torque-reduction request output on Output 4.
An optional VSS input is also available when the conversion uses an external speed sensor.
Open wiring schematic (PDF)CORE BENEFITS
More integration for your DSG swap
A central interface for CAN communication, driver inputs and the vehicle signals your conversion needs.
⇄
Separate CAN networks
Dedicated CAN0 for the DSG and CAN1 for the vehicle or ECU provide two connection points for your conversion.
↕
Paddle integration
Ground-switch inputs for shift up and shift down, plus a LIN connection for supported steering-wheel paddle modules.
◉
Vehicle outputs
Connect reverse lights, a starter-enable relay and a compatible VSS speedometer through dedicated outputs.
⌁
Updates & diagnostics
Wireless firmware updates, CAN communication status LEDs and CAN logging support setup and diagnostics.
Two 12-contact connectors for power, CAN, LIN and vehicle I/O.
CAN SIGNAL INTEGRATION
Dedicated connections for the DSG and the car
Connect the transmission network to CAN0 and the car or ECU network to CAN1. This arrangement gives the controller access to both sides of the conversion.
✓ Signal conversion and simulation for supported swap configurations.
✓ DSG speed requests for the VSS output, with VW TP2.0 communication for compatible older DSG gearboxes.
✓ Brake-pressure CAN data sent over ABS CAN.
✓ VE DSG Controller CAN protocol for integration with other CAN devices.
Select the setup for your particular gearbox, ECU and vehicle network. The number of CAN ports alone does not establish protocol compatibility.
EXTERNAL CAN DEVICES
Control your DSG from a CAN display or another CAN device
The DSG Controller accepts CAN bus input commands, allowing compatible displays and other CAN devices to operate the gear selector and send paddle-shift commands. CAN feedback frames let the connected device show the current transmission status.
↻
Gear selector commands
Request P, R, N, D, S or M over CAN bus, so a compatible external device can provide your selector controls.
↕
Paddle-shift commands
Send shift-up and shift-down commands over CAN bus from a display or another connected control device.
⇄
CAN feedback frames
Read the lever position, actual gear and shift-lock status to show the selected position, display the engaged gear and operate a shift-lock light.
Display / CAN device
Selector controls · shift buttons · status display
⇄
DSG Controller
CAN commands in · status feedback out
⇄
DSG gearbox
Lever position · actual gear · shift lock
Configure the external device to send and read the supported DSG Controller CAN messages.
External CAN controls work alongside the required VAG ECU with CAN bus; they do not replace it.
DRIVER INPUTS
Connect the controls your conversion uses
Bring paddle, brake and selector signals into one interface.
↕
Digital or LIN paddles
Separate ground-switch inputs accept upshift and downshift commands. The LIN connection allows integration with a compatible steering-wheel module.
◈
Brake & brake pressure
Connect a 12 V brake-switch signal. An optional brake-pressure sensor uses the pressure input, sensor 5 V supply and sensor ground.
↻
Rotary selector input
A dedicated analog input connects a rotary switch for gear selection. Match the selector wiring and configuration to the installation.
ADDITIONAL INTEGRATION
Functions for more involved conversions
Integrate additional driving and shift-control functions through the controller’s CAN and I/O connections. Available functions depend on the transmission, ECU, connected controls and configuration.
⚙
Launch control & kickdown
Integrates launch control with ESP enabled and kickdown functionality.
⇆
Torque coordination
Supports ECU torque correction and a dedicated torque-reduction request output on Output 4.
↗
Alternative shift controls
Control shifting from your phone or use a rotary switch as the gear selector.
PQ25 / Mk20 ABS speed integration
Provides a speed-signal fix for PQ25 / Mk20 ABS conversions affected by gear disengagement around 50–60 km/h and P0722 / G195 or P1793 / G196 fault codes.
FIRMWARE & DIAGNOSTICS
Wireless updates and CAN diagnostics
Update the DSG Controller wirelessly, monitor CAN communication with the status LEDs and record CAN traffic with the CAN logger.
Supports VW TP2.0 speed requests for older DSG gearboxes, brake-pressure data on ABS CAN and the VE DSG Controller CAN protocol.
Tools for setup and troubleshooting
• Wireless firmware updates
• CAN communication status LEDs
• CAN traffic logging
• VW TP2.0 speed requests for compatible older DSG gearboxes
• Brake-pressure data on ABS CAN
• VE DSG Controller CAN protocol
CHOOSE YOUR INTERFACE
DSG Controller or CAN Convertor DSG?
Choose around the signals and CAN integration required by your project.
CAN Convertor DSG
Paddle, VSS, reverse & starter integration
Core signal-integration functions
Separate car / ECU and DSG CAN connections
Single CAN connection
Brake-pressure & rotary-switch inputs
Consider the DSG Controller for these inputs
Torque-reduction request output
Consider the DSG Controller for this output
DSG Controller
Paddle, VSS, reverse & starter integration
Included among the controller’s functions
Separate car / ECU and DSG CAN connections
CAN0 for DSG + CAN1 for car / ECU
Brake-pressure & rotary-switch inputs
Dedicated brake-pressure and rotary-switch inputs
Torque-reduction request output
Torque-reduction request on Output 4
BEFORE YOU ORDER
Check the complete conversion
A compatible VAG ECU with CAN bus is required. The DSG Controller is an integration interface, not a standalone DSG controller.
The DSG Controller integrates the DQ250 DSG with a compatible VAG ECU and the vehicle’s electronics. Compatibility depends on the transmission control unit, VAG ECU, vehicle CAN signals and the functions you want to use.
For a useful compatibility check, send:
✓ Vehicle model and year
✓ Gearbox type and transmission / TCU part number
✓ Engine and ECU details
✓ ABS system and available speed source
✓ Paddle, selector and required output details
Plan the wiring around the gearbox, ECU and controls in your vehicle.
TECHNICAL REFERENCE
Connections and wiring
Two 12-contact connectors group the controller’s power, communication and vehicle signals. Download the wiring schematic for the installation layout.
BLACK CONNECTOR
Power, LIN & outputs
• Switched 12 V and main ground
• Reverse-light output
• Starter-enable relay output
• VSS speed output
• Torque-reduction request output
• LIN steering-wheel connection
• Brake and upshift inputs
• Sensor 5 V and ground
GREY CONNECTOR
CAN & sensor inputs
• CAN0 for DSG
• CAN1 for car / ECU
• Brake-pressure input
• Rotary-switch input
• Downshift input
• VSS speed input
• Additional inputs for RPM, throttle and boost
INSTALLATION
Power & network setup
• Switched supply must remain active while cranking
• 10 A fused power supply
• Controller ground close to the unit
• CAN termination matched to the network
• Starter-enable output drives a relay
QUESTIONS & ANSWERS
Frequently asked questions
▸ Is this a standalone DSG controller?
No. It requires a compatible VAG ECU with CAN bus and the DSG’s original transmission control unit. The DSG Controller integrates vehicle signals and CAN communication; it cannot operate the gearbox independently of the required VAG ECU.
▸ How does it differ from the CAN Convertor DSG?
The DSG Controller has separate DSG and car / ECU CAN connections, additional sensor and selector inputs, and a dedicated torque-reduction request output. Choose according to the requirements of the complete conversion.
▸ Can I keep a speedometer without CAN?
A VSS speed output is provided for compatible older clusters. Match the speed source and speedometer requirements to the installation.
▸ Can I connect steering-wheel paddles?
Dedicated ground-switch inputs accept shift-up and shift-down commands. A LIN connection is also available for a compatible steering-wheel module.
▸ What does the starter-enable output do?
It provides a 12 V relay-control output when the selector is in P or N. The relay is installed in the starter control circuit.
▸ Are wireless updates and CAN logging supported?
Yes. The controller supports wireless firmware updates and CAN traffic logging.
▸ Does it support every DSG gearbox?
Support must be checked for the exact gearbox and TCU, ECU and vehicle network. Send the details of your conversion before ordering.
▸ Can it request speed from an older DSG?
The controller supports VW TP2.0 speed requests on compatible older DSG gearboxes.
YOUR NEXT DSG PROJECT
Bring your DSG conversion together.
Dedicated DSG and vehicle CAN connections, paddle integration and vehicle outputs for conversions using a compatible VAG ECU with CAN bus.
€500.00 excl. VAT
Send your vehicle, VAG ECU and gearbox details for compatibility advice.